Fire protection for steel beams · Inverness
Fire protection for steel beams in Inverness
Steelwork, approvals and making good for fire protection for steel beams in Inverness and nearby.
- Free survey visit in Inverness
- Engineer's calculations arranged
- Building warrant handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What fire protection for steel beams involves in Inverness
Need fire protection for steel beams in Inverness? Our coverage runs across the Highlands, so nearby villages are included too. We survey the property, arrange the engineer's design, deal with The Highland Council, fit the steel and make good, all under one quote for IV1, IV2 and IV3 addresses.
A bare steel beam is strong at room temperature but loses much of its load-carrying capacity once it gets hot enough in a fire. If that beam holds up a floor or the walls above, it matters to everyone in the building. Fire protection slows the rate at which the steel heats up, buying time for people to get out safely.
What to expect
- A common fault is applying intumescent paint over the wrong primer, or over one of unknown type. The products must be compatible, so where steel was primed long ago the primer is identified or the surface is cleaned back before coating.
- Boxing is generally the lower-cost route for steel that will be hidden. Intumescent coatings cost more because of the product and the number of coats, and the price rises with the fire period and the size of the section.
- Boarding is fairly clean work, but coatings need a clean, dry and well-ventilated room at a suitable temperature. Dust from other trades can spoil the surface, so painting is normally scheduled once the messy work in that room is finished.
- Boxing a single beam usually takes around a day, plus skimming and drying. Intumescent coatings need each coat to dry before the next goes on, so they can take several days depending on the thickness required and the room temperature.
- Fire boarding should not be cut into casually later on. Downlights, cables and pipes pushed through the boxing can weaken it, so services are planned before boarding, and any openings are sealed with suitable fire-stopping materials.
Four stages, one team
Survey in Inverness
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building warrant
A building warrant is applied for from The Highland Council, and work starts only once the warrant has been granted.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building standards inspects it, and we make good.
Guide prices for fire protection for steel beams in Inverness
As a guide, budget £140–£550 per beam including VAT for fire protection to a steel beam in Inverness, based on published UK cost guides adjusted for prices in Scotland (-9%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Fire protection to a steel beam | £140–£550 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Steel beam replacement | £1,800–£5,000 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| Building warrant fee | £215–£435 | Statutory fee set by the estimated value of the work: £215 up to £5,000, rising on a sliding scale (fees from 1 April 2026) |
| Structural calculations for a beam | £230–£680 | Site measure or photos, beam and padstone design and calculations for building standards |
Figures include our approximate regional adjustment for prices in Scotland (-9%) and are rounded. How these figures are worked out.
Approvals in Inverness
In Scotland, structural alterations need a building warrant under the Building (Scotland) Act 2003, and work must not start until the warrant is granted. For Inverness, warrants are handled by The Highland Council's building standards service. When the work is finished, a completion certificate is submitted and has to be accepted by the council.
Scotland has no Party Wall Act. Work affecting a shared wall is governed by your title deeds and the general law, and in flats by the Tenements (Scotland) Act 2004, so it is sensible to agree the work with neighbours in writing before starting.
Local questions answered
What happens at the survey visit in Inverness?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Can you work on older or listed homes in Inverness?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Does a steel beam in a house need fire protection?
Usually, yes. Where a steel beam or column holds up part of the structure, building regulations normally require it to resist fire for a set period, commonly 30 minutes in a typical house. Building standards confirms what is needed for your property, and the protection is checked before the work is signed off.
Can I box in a steel beam with normal plasterboard?
Not where fire protection is required. Standard plasterboard is not designed to protect steel for a set period in a fire. Fire-rated plasterboard is used instead, fixed in the number of layers and with the fixings the system specifies, so the boxing performs as intended and passes when building standards checks it.
How thick does intumescent paint need to be on a steel beam?
There is no single figure. The thickness depends on the steel section, how many sides are exposed and the fire period required, and the coating manufacturer's data sets the dry film thickness for each case. The applied thickness is measured with a gauge once the coats have dried and recorded for building standards.
Do you cover Inverness for fire protection for steel beams?
Yes. We carry out fire protection for steel beams in Inverness and the IV1, IV2 and IV3 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.