Fire protection for steel beams · Borehamwood
Fire protection for steel beams in Borehamwood
Fire protection for steel beams for homes in WD6, WD7, designed by a structural engineer.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Fire protection for steel beams in Borehamwood: how it works
Planning fire protection for steel beams in Borehamwood? Our team covers WD6 and WD7 and the streets around them. We also work in nearby Watford, roughly 5.1 miles away. You get one written quote for the calculations, approvals, propping, steel and making good.
A bare steel beam is strong at room temperature but loses much of its load-carrying capacity once it gets hot enough in a fire. If that beam holds up a floor or the walls above, it matters to everyone in the building. Fire protection slows the rate at which the steel heats up, buying time for people to get out safely.
Things to plan for
- Steel does not burn, but it loses stiffness and strength as it heats. Protection is there to keep the temperature of the beam down for a set period, so the floor or walls it carries stay up while people leave.
- A common fault is applying intumescent paint over the wrong primer, or over one of unknown type. The products must be compatible, so where steel was primed long ago the primer is identified or the surface is cleaned back before coating.
- The fire resistance needed depends on the building and where the steel sits. In a typical two-storey house, elements of structure commonly need 30 minutes, but taller homes, flats and commercial premises can need more. The engineer and building control confirm the figure.
- Keep a record of what was fitted: the board type and number of layers, or the coating product, thickness readings and number of coats. Building control may ask for it, and it helps answer queries when the house is sold.
- Boxing is generally the lower-cost route for steel that will be hidden. Intumescent coatings cost more because of the product and the number of coats, and the price rises with the fire period and the size of the section.
From survey to sign-off in Borehamwood
Free visit
A short visit to Borehamwood to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
Guide prices for fire protection for steel beams in Borehamwood
As a guide, budget £160–£640 per beam including VAT for fire protection to a steel beam in Borehamwood, based on published UK cost guides adjusted for prices in the East of England (+6%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Fire protection to a steel beam | £160–£640 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Building control fees | £260–£690 | Building notice or full plans fee and inspections; varies by council or approver |
| Steel beam replacement | £2,100–£5,850 | Propping, removing the failed beam, new steel on proper bearings, approval and making good |
| RSJ supply and fit (single beam) | £850–£2,650 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
Figures include our approximate regional adjustment for prices in the East of England (+6%) and are rounded. How these figures are worked out.
Building control and neighbours in Borehamwood
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Fire protection for steel beams near Borehamwood
- Barnet 3.3 mi
- Bushey 3.6 mi
- Hadley Wood 4.7 mi
- Potters Bar 5.0 mi
- Watford 5.1 mi
- Finchley 5.1 mi
Questions about fire protection for steel beams in Borehamwood
Do you also work near Borehamwood?
Yes. We also cover nearby towns including Barnet, Bushey, Hadley Wood and Potters Bar.
How much does fire protection for steel beams cost in Borehamwood?
As a guide, budget £160–£640 per beam including VAT for fire protection to a steel beam in Borehamwood, based on published UK cost guides adjusted for prices in the East of England (+6%). The exact figure depends on the span, what the wall carries, access and the finish, and is fixed in writing once the scope is agreed.
My steel beam was fitted years ago without fire protection. What should I do?
Have it looked at and protected to current requirements. Unprotected steel can raise questions when you sell, and if the original work was never approved, a regularisation application to building control may be needed in England and Wales. We can survey the steel and price both the protection and the paperwork route.
Can I put downlights in a boxed-in steel beam?
Only with planning. Cutting holes in fire boarding can weaken its protection, so any lights in or near the boxing need to be designed in, using fire-rated fittings or suitable fire-stopping where the board is pierced. It is far easier to sort this out before the boxing goes up than to adapt it afterwards.
What is intumescent paint for steel beams?
Intumescent paint is a fire-protective coating that swells when heated, forming a thick insulating layer that slows the steel heating up. It lets you leave a beam on show while still meeting fire requirements. It must be applied at a specified thickness over a compatible primer, so it goes on to a written specification rather than like ordinary paint.
Do you cover Borehamwood for fire protection for steel beams?
Yes. We carry out fire protection for steel beams in Borehamwood and the WD6 and WD7 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.