Chimney breast removal · Armagh City, Banbridge and Craigavon
Chimney breast removal in Armagh City, Banbridge and Craigavon
Survey, engineer's design and installation of chimney breast removal anywhere in Armagh City, Banbridge and Craigavon.
- Survey, design and installation in one
- Covering BT25, BT31, BT32, BT60
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Chimney breast removal in Armagh City, Banbridge and Craigavon: how it works
Chimney breast removal is taking out the projecting brickwork that houses the flues from fireplaces, usually to gain floor space or straighten a wall. If any of the breast or stack above stays in place, it must be carried on steel or another support the engineer designs and building control accepts, so it is never left unsupported.
Looking for chimney breast removal in Armagh City, Banbridge and Craigavon? Coverage takes in Banbridge, Portadown and Craigavon and everywhere in between. Our teams handle the calculations, the building control approval, the propping and the steel itself, and leave the opening ready for plastering and decoration.
Key points for your project
- Chimney brickwork is heavy and dirty. Even a single breast produces a lot of rubble and soot, so a skip or waste collection is planned in advance, and floors, stairs and furniture along the route out are protected.
- A flue still serving a gas fire, boiler or wood burner cannot be removed until that appliance is disconnected and an alternative arranged. Work on any gas appliance or pipe must, by law, be done by a Gas Safe registered engineer.
- Some owners remove breasts in the loft to make space for a conversion while keeping the stack on the roof. That leaves the stack carried at loft level on steel or another support, which the engineer must design and building control must approve before work starts.
- Gallows brackets are steel angle brackets fixed into the wall to hold a breast above. They are often not accepted where the remaining masonry is heavy or sits against the neighbour's breast, so the engineer and building control decide which support method is suitable.
- A chimney closed off at both ends can trap moisture and cause damp patches on the walls. Where part of a flue remains, a vent at room level and a ventilated cap on the pot keep air moving through it.
How the job runs in Armagh City, Banbridge and Craigavon
Survey in Armagh City, Banbridge and Craigavon
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
A full plans application or building notice goes to Armagh City, Banbridge and Craigavon Borough Council under the Building Regulations (Northern Ireland) 2012 before work begins.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
What does chimney breast removal cost in Armagh City, Banbridge and Craigavon?
As a guide, budget £1,300–£2,600 including VAT for chimney breast removal (ground floor) in Armagh City, Banbridge and Craigavon, based on published UK cost guides adjusted for prices in Northern Ireland (-14%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Chimney breast removal (ground floor) | £1,300–£2,600 | Ground-floor breast removed, steel to support the breast above, building control and making good |
| Structural calculations for a beam | £220–£640 | Site measure or photos, beam and padstone design and calculations for building control |
| Loft conversion steels | £2,150–£5,150 | Supply and fit of floor and ridge steels on padstones, including lifting into the roof space |
Figures include our approximate regional adjustment for prices in Northern Ireland (-14%) and are rounded. How these figures are worked out.
Approvals in Armagh City, Banbridge and Craigavon
Building control in Armagh City, Banbridge and Craigavon is run by Armagh City, Banbridge and Craigavon Borough Council. Beams and new openings are controlled work under the Northern Ireland regulations, so we apply before anything is removed and the steel is inspected before it is covered.
Northern Ireland has no Party Wall Act, so there is no statutory notice to serve. Where the steel bears into a shared wall, the title deeds and the general law apply, and agreeing the work with your neighbour in writing first is good practice.
Questions about chimney breast removal in Armagh City, Banbridge and Craigavon
Who approves chimney breast removal in Armagh City, Banbridge and Craigavon?
Structural work in Armagh City, Banbridge and Craigavon needs a full plans application or building notice to Armagh City, Banbridge and Craigavon Borough Council. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Can you work on older or listed homes in Armagh City, Banbridge and Craigavon?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Can I remove a chimney breast downstairs and keep the fireplace upstairs?
Usually, as long as the upstairs breast and its flue stay intact and are carried on a support the engineer designs for that load. Building control must approve the arrangement. If the upstairs fireplace has a gas fire, any work on it or its supply must be carried out by a Gas Safe registered engineer.
How long does chimney breast removal take?
A ground-floor breast with a steel beam supporting the masonry above usually takes two to four working days, including propping, fitting the steel, removing the brickwork and basic making good. Full removal from ground floor to roof takes longer because of scaffolding, roofing work and weather, and plaster needs time to dry afterwards.
Should I remove the chimney stack as well?
It often makes sense if the breast is coming out on every floor, because then nothing is left to support. It needs scaffolding and roof repairs, and in terraces the stack is often shared, so your side may not be removable without affecting your neighbour's. The engineer and building control confirm what is possible.
Will removing a chimney breast cause damp?
It can if the remaining flue is sealed with no airflow, because moisture and condensation get trapped inside. Fitting a vent in the remaining breast or wall and a ventilated cap on the chimney pot keeps air moving. If the stack is removed and the roof made good, the risk from the flue goes away.