Bi-fold & sliding door openings · Crawley
Bi-fold & sliding door openings in Crawley
Bi-fold & sliding door openings for homes in RH10, RH11, designed by a structural engineer.
- Survey, design and installation in one
- Covering RH10, RH11
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning bi-fold & sliding door openings in Crawley
We carry out bi-fold & sliding door openings in Crawley, covering the RH10 and RH11 postcode districts. The wider West Sussex area is covered as well. The job starts with a free survey visit so the engineer's calculations are based on your actual walls, floors and loads.
We coordinate the structure with your door supplier's sizes, so the finished opening matches the frame. The survey visit, structural calculations from a qualified engineer, building control, propping, steel, cavity trays, weather protection while the wall is open and making good are all covered in one itemised written quote.
Worth knowing before you start
- Both leaves of a cavity wall need support over the opening. Depending on the design, the outer brickwork may sit on a plate fixed to the beam or on a separate external lintel, and the engineer specifies which suits the loads and the look.
- The structural work for a typical bi-fold opening usually takes three to five working days. Doors are often made to order, so the steel goes in once opening sizes are confirmed and the doors are fitted soon after.
- Very wide openings, or ones that run close to the corner of the house, may leave too little wall for the beam to bear on. In that case the engineer may specify steel columns or a goalpost frame standing on its own foundations.
- Glazed doors need a stiffer beam than a plain opening of the same width. If the steel bends even slightly under load, folding panels can bind, sliders can stick and glass can be stressed, so the engineer sets a tighter deflection limit for door openings.
- Replacing a rear window with doors in a house is usually permitted development, but front elevations, listed buildings, flats and homes where permitted development rights have been removed may need planning permission or another consent.
What happens, step by step
Free visit
A short visit to Crawley to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
Guide prices for bi-fold & sliding door openings in Crawley
As a guide, budget £2,800–£7,850 including VAT for rear wall opening for bi-fold or sliding doors in Crawley, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Rear wall opening for bi-fold or sliding doors | £2,800–£7,850 | External wall opened up to about 5 m with steel, propping, cavity tray and making good (doors supplied separately) |
| Steel goalpost frame | £2,250–£6,700 | Two posts and a beam bolted as a frame, pad foundations, base plates and fitting |
| Lintel replacement | £450–£1,340 per lintel | Propping, removing the old lintel, new lintel set on beds and brickwork made good |
| Structural calculations for a beam | £280–£840 | Site measure or photos, beam and padstone design and calculations for building control |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building control and neighbours in Crawley
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Bi-fold & sliding door openings near Crawley
- Horley 4.4 mi
- Horsham 7.2 mi
- East Grinstead 7.7 mi
- Reigate 8.6 mi
- Haywards Heath 8.7 mi
- Redhill 8.8 mi
Questions about bi-fold & sliding door openings in Crawley
Who approves bi-fold & sliding door openings in Crawley?
Structural work in Crawley needs a building notice or full plans application to the local council's building control team or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Can I stay at home while the work is done in Crawley?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
Do I need a steel beam for bi-fold doors?
Usually, yes. Bi-fold and sliding doors need wide openings, and in a load-bearing external wall that span is normally carried on steel. The engineer designs it for strength and stiffness, because glazed doors can stick or be damaged if the beam deflects. A small opening under light loads might only need a lintel, but that is the engineer's call.
How long does it take to make an opening for bi-fold doors?
The structural opening usually takes three to five working days, including propping, cutting out the wall, fitting the steel and outer leaf support, and forming the reveals. The doors can then be fitted, with inside making good and outside brickwork finishing following on. Lead times on made-to-order doors affect the overall timeline more than the steelwork.
Why does the beam need to be stiffer for glazed doors?
Because glazed doors tolerate very little movement. Every beam bends slightly under load, and with bi-folds or sliders that movement can make panels bind, tracks drag or glass crack. The engineer sets a stricter deflection limit for these openings, which often means a heavier section than strength alone would need.
Do you also work near Crawley?
Yes. We also cover nearby towns including Horley, Horsham, East Grinstead and Reigate.