Bi-fold & sliding door openings · Felling
Bi-fold & sliding door openings in Felling
Steelwork, approvals and making good for bi-fold & sliding door openings in Felling and nearby.
- Free survey visit in Felling
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning bi-fold & sliding door openings in Felling
If you live in Felling, bi-fold & sliding door openings can usually be planned and priced after a single survey visit. It sits about 2.2 miles from Newcastle upon Tyne, which we also cover. We cover NE8, NE9, NE10 and NE11, and we fix the price in writing once the layout and scope are agreed.
Replacing a window or narrow patio door with a full run of bi-fold or sliding doors opens a room to the garden. Because it is an external wall, the opening usually carries the first floor, the wall above and sometimes roof loads, and the new steel has to work with the doors as well as hold the house up.
Things to plan for
- New glazed doors must meet the energy efficiency requirements of the building regulations, and a wide opening adds a large area of glazing to the house. The door supplier normally provides the performance data that building control needs.
- Both leaves of a cavity wall need support over the opening. Depending on the design, the outer brickwork may sit on a plate fixed to the beam or on a separate external lintel, and the engineer specifies which suits the loads and the look.
- New brickwork at the reveals and above the opening should match the existing in colour, size and bond. Sound bricks from the wall being removed are often cleaned and reused, and the mortar colour is matched as closely as possible.
- Replacing a rear window with doors in a house is usually permitted development, but front elevations, listed buildings, flats and homes where permitted development rights have been removed may need planning permission or another consent.
- The house is open to the weather between taking out the wall and fitting the doors. Temporary sheeting or a boarded frame keeps rain out and the house secure, so the gap between the structural work and door fitting should be kept short.
How the job runs in Felling
Survey in Felling
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to Gateshead Council, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
What do bi-fold & sliding door openings cost in Felling?
As a guide, budget £2,300–£6,500 including VAT for rear wall opening for bi-fold or sliding doors in Felling, based on published UK cost guides adjusted for prices in the North East (-7%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Rear wall opening for bi-fold or sliding doors | £2,300–£6,500 | External wall opened up to about 5 m with steel, propping, cavity tray and making good (doors supplied separately) |
| RSJ supply and fit (single beam) | £740–£2,320 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Opening into a rear extension | £2,300–£6,500 | Original rear wall removed with a beam or goalpost, approvals and propping, coordinated with the extension build |
| Widening an internal doorway | £930–£2,320 | Opening widened with a new lintel or short beam, approval where structural, and making good |
Figures include our approximate regional adjustment for prices in the North East (-7%) and are rounded. How these figures are worked out.
Building control and neighbours in Felling
For Felling, building control is provided by Gateshead Council, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Questions about bi-fold & sliding door openings in Felling
Do you also work near Felling?
Yes. We also cover nearby towns including Gateshead, Newcastle upon Tyne, Hebburn and Wallsend.
What happens at the survey visit in Felling?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Why does the beam need to be stiffer for glazed doors?
Because glazed doors tolerate very little movement. Every beam bends slightly under load, and with bi-folds or sliders that movement can make panels bind, tracks drag or glass crack. The engineer sets a stricter deflection limit for these openings, which often means a heavier section than strength alone would need.
Do I need planning permission for bi-fold doors?
Usually not for a rear opening in a house, as this generally falls within permitted development. Planning or another consent may be needed for front elevations, flats, listed buildings, conservation areas with extra controls, or homes where permitted development rights have been removed. We flag this at survey so you can check before work is booked.
Can I have a level threshold with bi-fold doors?
Often yes, but it has to be designed. The inside floor, outside paving and drainage all need to work together so water cannot run in, usually with a drainage channel outside and the right damp-proof detail under the door frame. We look at levels at the survey and plan the threshold with the door supplier.