Bi-fold & sliding door openings · Hampton
Bi-fold & sliding door openings in Hampton
Bi-fold & sliding door openings for homes in KT1, TW1, TW2, designed by a structural engineer.
- Survey, design and installation in one
- Covering KT1, TW1, TW2
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What bi-fold & sliding door openings involve in Hampton
We cover bi-fold & sliding door openings in Hampton (KT1, TW1, TW2) and the streets around it. We also cover the surrounding towns and villages in London. Each job is designed by a structural engineer and approved through local building control before work begins.
Replacing a window or narrow patio door with a full run of bi-fold or sliding doors opens a room to the garden. Because it is an external wall, the opening usually carries the first floor, the wall above and sometimes roof loads, and the new steel has to work with the doors as well as hold the house up.
Things to plan for
- Replacing a rear window with doors in a house is usually permitted development, but front elevations, listed buildings, flats and homes where permitted development rights have been removed may need planning permission or another consent.
- The structural work for a typical bi-fold opening usually takes three to five working days. Doors are often made to order, so the steel goes in once opening sizes are confirmed and the doors are fitted soon after.
- Both leaves of a cavity wall need support over the opening. Depending on the design, the outer brickwork may sit on a plate fixed to the beam or on a separate external lintel, and the engineer specifies which suits the loads and the look.
- Very wide openings, or ones that run close to the corner of the house, may leave too little wall for the beam to bear on. In that case the engineer may specify steel columns or a goalpost frame standing on its own foundations.
- A wide glazed opening changes the security of the back of the house. During the works the opening is boarded at night if the doors are not yet fitted, and it is worth checking the locking and glass specification of the doors you choose.
Four stages, one team
Survey in Hampton
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
What do bi-fold & sliding door openings cost in Hampton?
As a guide, budget £3,200–£8,950 including VAT for rear wall opening for bi-fold or sliding doors in Hampton, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Rear wall opening for bi-fold or sliding doors | £3,200–£8,950 | External wall opened up to about 5 m with steel, propping, cavity tray and making good (doors supplied separately) |
| Steel goalpost frame | £2,550–£7,700 | Two posts and a beam bolted as a frame, pad foundations, base plates and fitting |
| Widening an internal doorway | £1,300–£3,200 | Opening widened with a new lintel or short beam, approval where structural, and making good |
| RSJ supply and fit (single beam) | £1,000–£3,200 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Building control and neighbours in Hampton
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Bi-fold & sliding door openings near Hampton
- Hanworth 1.5 mi
- Sunbury-on-Thames 2.3 mi
- Walton-on-Thames 2.7 mi
- Esher 3.0 mi
- Feltham 3.0 mi
- Surbiton 3.3 mi
Questions about bi-fold & sliding door openings in Hampton
Do you also work near Hampton?
Yes. We also cover nearby towns including Hanworth, Sunbury-on-Thames, Walton-on-Thames and Esher.
Do I need a party wall agreement for bi-fold & sliding door openings in Hampton?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
Do I need a steel beam for bi-fold doors?
Usually, yes. Bi-fold and sliding doors need wide openings, and in a load-bearing external wall that span is normally carried on steel. The engineer designs it for strength and stiffness, because glazed doors can stick or be damaged if the beam deflects. A small opening under light loads might only need a lintel, but that is the engineer's call.
Will the house be open to the weather while the wall is out?
Only briefly, and it is protected throughout. Once the wall is out, the opening is sheeted or boarded so it stays weathertight and secure until the doors arrive. Timing the structural work close to the door delivery date keeps that period as short as possible.
Do I need planning permission for bi-fold doors?
Usually not for a rear opening in a house, as this generally falls within permitted development. Planning or another consent may be needed for front elevations, flats, listed buildings, conservation areas with extra controls, or homes where permitted development rights have been removed. We flag this at survey so you can check before work is booked.
Do you cover Hampton for bi-fold & sliding door openings?
Yes. We carry out bi-fold & sliding door openings in Hampton and the KT1, TW1, TW2, TW11 and TW12 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.