Bi-fold & sliding door openings · Sevenoaks
Bi-fold & sliding door openings in Sevenoaks
Bi-fold & sliding door openings for homes in TN13, TN14, designed by a structural engineer.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our bi-fold & sliding door openings service in Sevenoaks
Sevenoaks has a mix of housing, and bi-fold & sliding door openings need a slightly different approach in each. We also work in nearby Maidstone, roughly 14.2 miles away. Whatever the age of the property, the steel goes in on proper bearings with temporary support in place throughout.
Replacing a window or narrow patio door with a full run of bi-fold or sliding doors opens a room to the garden. Because it is an external wall, the opening usually carries the first floor, the wall above and sometimes roof loads, and the new steel has to work with the doors as well as hold the house up.
Things to plan for
- The house is open to the weather between taking out the wall and fitting the doors. Temporary sheeting or a boarded frame keeps rain out and the house secure, so the gap between the structural work and door fitting should be kept short.
- New glazed doors must meet the energy efficiency requirements of the building regulations, and a wide opening adds a large area of glazing to the house. The door supplier normally provides the performance data that building control needs.
- A wide glazed opening changes the security of the back of the house. During the works the opening is boarded at night if the doors are not yet fitted, and it is worth checking the locking and glass specification of the doors you choose.
- Replacing a rear window with doors in a house is usually permitted development, but front elevations, listed buildings, flats and homes where permitted development rights have been removed may need planning permission or another consent.
- Very wide openings, or ones that run close to the corner of the house, may leave too little wall for the beam to bear on. In that case the engineer may specify steel columns or a goalpost frame standing on its own foundations.
From survey to sign-off in Sevenoaks
Survey in Sevenoaks
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
Guide prices for bi-fold & sliding door openings in Sevenoaks
As a guide, budget £2,800–£7,850 including VAT for rear wall opening for bi-fold or sliding doors in Sevenoaks, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Rear wall opening for bi-fold or sliding doors | £2,800–£7,850 | External wall opened up to about 5 m with steel, propping, cavity tray and making good (doors supplied separately) |
| RSJ supply and fit (single beam) | £900–£2,800 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Opening into a rear extension | £2,800–£7,850 | Original rear wall removed with a beam or goalpost, approvals and propping, coordinated with the extension build |
| Steel goalpost frame | £2,250–£6,700 | Two posts and a beam bolted as a frame, pad foundations, base plates and fitting |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building control and neighbours in Sevenoaks
For Sevenoaks, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Bi-fold & sliding door openings in Sevenoaks: your questions
Can I stay at home while the work is done in Sevenoaks?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
Do I need a party wall agreement for bi-fold & sliding door openings in Sevenoaks?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
What does a bi-fold opening quote include?
Our itemised written quote covers the survey, calculations, building control, propping, removing the wall, steel and padstones, outer leaf support, cavity trays and closers, temporary weather protection and making good. Doors, threshold drainage and patio work are shown separately unless agreed. The price is fixed in writing once the opening size and specification are agreed.
Can I have a level threshold with bi-fold doors?
Often yes, but it has to be designed. The inside floor, outside paving and drainage all need to work together so water cannot run in, usually with a drainage channel outside and the right damp-proof detail under the door frame. We look at levels at the survey and plan the threshold with the door supplier.
Do I need a steel beam for bi-fold doors?
Usually, yes. Bi-fold and sliding doors need wide openings, and in a load-bearing external wall that span is normally carried on steel. The engineer designs it for strength and stiffness, because glazed doors can stick or be damaged if the beam deflects. A small opening under light loads might only need a lintel, but that is the engineer's call.
Do you also work near Sevenoaks?
Yes. We also cover nearby towns including Tonbridge, Swanley, Tunbridge Wells and Caterham.