Bi-fold & sliding door openings · Armagh City, Banbridge and Craigavon
Bi-fold & sliding door openings in Armagh City, Banbridge and Craigavon
Survey, engineer's design and installation of bi-fold & sliding door openings anywhere in Armagh City, Banbridge and Craigavon.
- Survey, design and installation in one
- Covering BT25, BT31, BT32, BT60
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What bi-fold & sliding door openings involve in Armagh City, Banbridge and Craigavon
Bi-fold and sliding door openings are wide gaps formed in an external wall, usually at the back of the house, to take a run of folding or sliding glazed doors. A steel beam carries the wall, floor and roof loads above, and it is designed stiff enough that its movement does not press on the glass or stop the doors running.
If you are planning bi-fold & sliding door openings in Armagh City, Banbridge and Craigavon, the order of work matters as much as the steel: survey, calculations, approval, propping, installation, inspection and making good. Coverage takes in Banbridge, Portadown and Craigavon and everywhere in between. We run that sequence for you as one job with one point of contact.
Key points for your project
- Very wide openings, or ones that run close to the corner of the house, may leave too little wall for the beam to bear on. In that case the engineer may specify steel columns or a goalpost frame standing on its own foundations.
- New glazed doors must meet the energy efficiency requirements of the building regulations, and a wide opening adds a large area of glazing to the house. The door supplier normally provides the performance data that building control needs.
- External walls can have gas meters, boiler flues, soil pipes, outside taps or cables near the new opening. These are found at survey and moved by the right trade, with any gas pipework done by a Gas Safe registered engineer as the law requires.
- Both leaves of a cavity wall need support over the opening. Depending on the design, the outer brickwork may sit on a plate fixed to the beam or on a separate external lintel, and the engineer specifies which suits the loads and the look.
- New brickwork at the reveals and above the opening should match the existing in colour, size and bond. Sound bricks from the wall being removed are often cleaned and reused, and the mortar colour is matched as closely as possible.
Four stages, one team
Survey in Armagh City, Banbridge and Craigavon
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
A full plans application or building notice goes to Armagh City, Banbridge and Craigavon Borough Council under the Building Regulations (Northern Ireland) 2012 before work begins.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
How much should I budget in Armagh City, Banbridge and Craigavon?
As a guide, budget £2,150–£6,000 including VAT for rear wall opening for bi-fold or sliding doors in Armagh City, Banbridge and Craigavon, based on published UK cost guides adjusted for prices in Northern Ireland (-14%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Rear wall opening for bi-fold or sliding doors | £2,150–£6,000 | External wall opened up to about 5 m with steel, propping, cavity tray and making good (doors supplied separately) |
| Steel goalpost frame | £1,700–£5,150 | Two posts and a beam bolted as a frame, pad foundations, base plates and fitting |
| Structural calculations for a beam | £220–£640 | Site measure or photos, beam and padstone design and calculations for building control |
| Lintel replacement | £340–£1,030 per lintel | Propping, removing the old lintel, new lintel set on beds and brickwork made good |
Figures include our approximate regional adjustment for prices in Northern Ireland (-14%) and are rounded. How these figures are worked out.
Approvals in Armagh City, Banbridge and Craigavon
Removing a load-bearing wall in Northern Ireland needs building control approval from the council. Armagh City, Banbridge and Craigavon Borough Council covers Armagh City, Banbridge and Craigavon. The engineer's calculations support the application, and a completion certificate is issued after the final inspection.
Northern Ireland has no Party Wall Act, so there is no statutory notice to serve. Where the steel bears into a shared wall, the title deeds and the general law apply, and agreeing the work with your neighbour in writing first is good practice.
Questions about bi-fold & sliding door openings in Armagh City, Banbridge and Craigavon
Which towns in Armagh City, Banbridge and Craigavon do you cover?
We cover towns including Craigavon, Portadown and Banbridge, plus the villages and smaller towns around them.
Can you work on older or listed homes in Armagh City, Banbridge and Craigavon?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Why does the beam need to be stiffer for glazed doors?
Because glazed doors tolerate very little movement. Every beam bends slightly under load, and with bi-folds or sliders that movement can make panels bind, tracks drag or glass crack. The engineer sets a stricter deflection limit for these openings, which often means a heavier section than strength alone would need.
Will the house be open to the weather while the wall is out?
Only briefly, and it is protected throughout. Once the wall is out, the opening is sheeted or boarded so it stays weathertight and secure until the doors arrive. Timing the structural work close to the door delivery date keeps that period as short as possible.
What does a bi-fold opening quote include?
Our itemised written quote covers the survey, calculations, building control, propping, removing the wall, steel and padstones, outer leaf support, cavity trays and closers, temporary weather protection and making good. Doors, threshold drainage and patio work are shown separately unless agreed. The price is fixed in writing once the opening size and specification are agreed.
Do I need planning permission for bi-fold doors?
Usually not for a rear opening in a house, as this generally falls within permitted development. Planning or another consent may be needed for front elevations, flats, listed buildings, conservation areas with extra controls, or homes where permitted development rights have been removed. We flag this at survey so you can check before work is booked.