Wider doorways & openings · Derry/Londonderry
Wider doorways & openings in Derry/Londonderry
Wider doorways & openings for homes in BT47, BT48, designed by a structural engineer.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Wider doorways & openings in Derry/Londonderry: how it works
Our wider doorways & openings service in Derry/Londonderry covers everything from the first visit to the completion paperwork. Our coverage runs across Derry City and Strabane, so nearby villages are included too. Postcode districts we cover here include BT47 and BT48.
Not every layout change needs a whole wall out. Widening a cramped doorway, adding a second door into a room or forming a wide opening between hall and living room can change how a home flows while keeping most of the wall, along with its storage space and furniture positions.
Things to plan for
- Hallway walls are often load-bearing because they line up with walls upstairs and carry the floor joists or the stairs. A wall that sounds hollow when knocked is usually a stud partition, but older homes can have timber walls that still carry loads, so the engineer checks.
- Openings are cut with a masonry saw where possible rather than broken out with a hammer. Clean cuts keep the brickwork either side sound, give a straighter edge for plastering and send less vibration through the rest of the wall.
- Standard internal doors come in set widths, so it makes sense to size the opening to suit an off-the-shelf door and lining. Odd sizes need made-to-measure doors and linings, which take longer to arrange.
- Older door surrounds and walls can hide asbestos in textured coatings, insulating board above doors or panelling. In buildings built before 2000 it must be identified before the wall is cut, so a refurbishment survey of the area is arranged where there is a risk.
- For a modest increase in width, a lintel may be all that is needed, while a wider opening carrying a floor or wall usually needs steel. The engineer chooses the type and size from the actual loads, never from the opening width alone.
Four stages, one team
Free visit
A short visit to Derry/Londonderry to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
A full plans application or building notice goes to Derry City and Strabane District Council under the Building Regulations (Northern Ireland) 2012 before work begins.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
How much should I budget in Derry/Londonderry?
As a guide, budget £860–£2,150 including VAT for widening an internal doorway in Derry/Londonderry, based on published UK cost guides adjusted for prices in Northern Ireland (-14%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Widening an internal doorway | £860–£2,150 | Opening widened with a new lintel or short beam, approval where structural, and making good |
| Load-bearing wall removal with steel beam | £1,700–£4,300 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| RSJ supply and fit (single beam) | £690–£2,150 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Building control fees | £220–£560 | Building notice or full plans fee and inspections; varies by council or approver |
Figures include our approximate regional adjustment for prices in Northern Ireland (-14%) and are rounded. How these figures are worked out.
Building control and neighbours in Derry/Londonderry
In Northern Ireland, structural work comes under the Building Regulations (Northern Ireland) 2012 and is approved by the local council's building control. For Derry/Londonderry that is Derry City and Strabane District Council. We submit a full plans application or building notice before work starts and book the inspections.
The Party Wall etc. Act does not extend to Northern Ireland. Shared walls are dealt with under your title and the general law, so we recommend agreeing access and the work with your neighbour before it starts.
Local questions answered
Do I need a party wall agreement for wider doorways & openings in Derry/Londonderry?
There is no Party Wall Act in Northern Ireland. Your title deeds and the general law apply instead, so agree the work with your neighbour in writing before it starts.
What happens at the survey visit in Derry/Londonderry?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
How wide can I make a doorway?
That depends on the wall, what it carries and how much solid wall is left at each side for the support to bear on, and a structural engineer sets the limit. Many people go from a single door to a double-width opening, and beyond that the job starts to become a partial wall removal.
What is included in the price for a wider doorway?
The itemised written quote lists the survey, any engineer's calculations and building control fees, propping, cutting the opening, the lintel or steel, linings or plastered reveals, and making good. Moving services, supplying doors and flooring joins appear as separate lines. The price is fixed in writing once the size and finish are agreed.
How long does it take to widen a doorway?
The structural part usually takes one to two working days: propping, cutting the opening, fitting the lintel or beam and packing it. Plastering follows, then a few days of drying before linings are painted or a new door is hung. Building control inspection fits in once the support is in place.