Side return extension steels · Eastleigh
Side return extension steels in Eastleigh
Side return extension steels for homes in SO50, SO53, designed by a structural engineer.
- Free survey visit in Eastleigh
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our side return extension steels service in Eastleigh
We carry out side return extension steels in Eastleigh, covering the SO50 and SO53 postcode districts. We also work in nearby Southampton, roughly 4.9 miles away. The job starts with a free survey visit so the engineer's calculations are based on your actual walls, floors and loads.
Many Victorian and Edwardian terraces have a narrow back wing, often called an outrigger, with a strip of yard down one side. Infilling that strip turns a galley kitchen into a wide family room, but the outrigger's side wall usually holds up a bathroom or bedroom above, so it has to be replaced with steel.
Things to plan for
- Propping a side return is awkward because space in a narrow kitchen is tight and the infill side is often open ground. Props outside may stand on temporary pads or boards, set so they do not sink or shift in wet weather.
- Fitting the steel frame for a side return usually takes a few working days on site, depending on how many beams and columns there are. It is scheduled with the builder so the new space can be roofed and weathertight soon after the old wall comes down.
- Many outrigger kitchens have a chimney breast on the side wall being removed or on the party wall. Its position affects where beams can bear, and if any part of the breast is taken out, what remains above has to be supported as the engineer specifies.
- The number of beams, columns and connections drives steel cost more than the length of the side return alone. Keep the calculations, any party wall paperwork and the completion certificate together for when the house is sold.
- Glazed roofs over side returns are usually made to measure and need an edge that stays straight and level. The engineer may set a stiffer limit on how far the steel can deflect so the glazing is not stressed once loaded.
From survey to sign-off in Eastleigh
Survey in Eastleigh
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
Guide prices for side return extension steels in Eastleigh
As a guide, budget £3,900–£9,500 including VAT for side return extension steelwork in Eastleigh, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Side return extension steelwork | £3,900–£9,500 | Beams and posts along the old side wall line, propping and approvals (extension build extra) |
| Opening into a rear extension | £2,800–£7,850 | Original rear wall removed with a beam or goalpost, approvals and propping, coordinated with the extension build |
| Fire protection to a steel beam | £170–£670 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Temporary works and propping | £170–£560 | Props, spreaders, needles and sole plates for a typical opening, installed and struck |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building control and neighbours in Eastleigh
For Eastleigh, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Side return extension steels near Eastleigh
- Southampton 4.9 mi
- Winchester 6.9 mi
- Totton 6.9 mi
- Hythe 7.7 mi
- Fareham 10.9 mi
- Waterlooville 15.1 mi
Side return extension steels in Eastleigh: your questions
Do you also work near Eastleigh?
Yes. We also cover nearby towns including Southampton, Winchester, Totton and Hythe.
Can you work on older or listed homes in Eastleigh?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
Do I need planning permission for a side return extension?
It depends on the house and where it is. Some side return infills can be built under permitted development, but the rules for side extensions are restrictive, and conservation areas and listed buildings add further controls. Check with your local planning authority or architect before committing to a design.
Do I need a party wall agreement for a side return extension?
In England and Wales it is very likely. Building on or near the boundary, excavating close to the neighbour's foundations or cutting into a shared wall can all be notifiable under the Party Wall etc. Act 1996. Notices are arranged through a party wall surveyor on your behalf, and we do not give legal advice.
Can the steel beam be left exposed in a side return?
Yes, and many people like the look of exposed steel under a glazed roof. It usually still needs fire protection, so it is coated with an intumescent paint system to the specified thickness, then finished in your chosen colour. The engineer and building control confirm what protection is required.