Load-bearing wall removal · Feltham
Load-bearing wall removal in Feltham
Steelwork, approvals and making good for load-bearing wall removal in Feltham and nearby.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Feltham and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Load-bearing wall removal in Feltham: how it works
If you live in Feltham, load-bearing wall removal can usually be planned and priced after a single survey visit. We also cover the surrounding towns and villages in London. We cover TW2, TW3, TW4, TW5 and TW6, and we fix the price in writing once the layout and scope are agreed.
We handle the whole job: a survey visit, structural calculations from a qualified engineer, building control, temporary propping, the steel itself, and making good afterwards. You get one itemised written quote and one team to deal with from first visit to sign-off.
What to expect
- The beam size depends on the span, what sits above and how the ends are supported. Two walls that look the same can need very different steel, which is why every beam is sized from calculations rather than guessed.
- Most single-wall removals in a typical house take two to five working days on site for the structural part. Plastering, drying out and decorating follow on, and building control visits fit around those stages.
- Older homes can hide surprises such as weak lime mortar, timber lintels or a wall with no proper footing. Where the engineer needs something extra, we price it before any work starts rather than after.
- Cables, pipes, radiators and sometimes gas runs pass through internal walls. These are traced at the survey so they can be rerouted by the right trade before or during the work, not discovered halfway through.
- Each end of the beam needs a solid bearing. Padstones spread the point load into the masonry below, and if the wall underneath is weak the engineer may call for a steel column or a new pad foundation instead.
Four stages, one team
Survey in Feltham
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
How much should I budget in Feltham?
As a guide, budget £2,550–£6,400 including VAT for load-bearing wall removal with steel beam in Feltham, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Load-bearing wall removal with steel beam | £2,550–£6,400 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
| Through-lounge knock-through | £3,200–£7,050 | Wall between front and back reception rooms, steel beam, approvals, plastering and floor infill |
| Kitchen-diner knock-through | £3,200–£7,700 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
| Structural calculations for a beam | £320–£960 | Site measure or photos, beam and padstone design and calculations for building control |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Building control and neighbours in Feltham
In England, taking out a load-bearing wall or putting in a beam is building work under the Building Regulations 2010. It needs approval from building control, either the local council's building control team or a registered building control approver, through a full plans application or a building notice. Part A covers the structure and Part B covers fire safety, which is why steel in homes is usually fire protected.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Questions about load-bearing wall removal in Feltham
Who approves load-bearing wall removal in Feltham?
Structural work in Feltham needs a building notice or full plans application to the local council's building control team or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
How much does load-bearing wall removal cost in Feltham?
As a guide, budget £2,550–£6,400 including VAT for load-bearing wall removal with steel beam in Feltham, based on published UK cost guides adjusted for London prices (+28%). The exact figure depends on the span, what the wall carries, access and the finish, and is fixed in writing once the scope is agreed.
How do I know if my wall is load-bearing?
Clues include floor joists that run across the top of the wall, a wall directly above it upstairs, and a wall that is solid brick or block rather than a hollow stud partition. None of these is proof on its own. A structural engineer checks on site and confirms it before any work is planned.
What happens if the wall is shared with my neighbour?
In England and Wales, cutting into a party wall to take the end of a beam is covered by the Party Wall etc. Act 1996, and notice must be served on the neighbour before work starts. Scotland and Northern Ireland have no equivalent Act, so the title deeds and the general law apply instead.
How long does it take to remove a load-bearing wall?
For a typical house the structural part usually takes two to five working days: propping, taking the wall out, fitting the steel and packing it tight. Plastering and decorating follow once building control has inspected the steel.