Load-bearing wall removal · East Lothian
Load-bearing wall removal in East Lothian
Load-bearing wall removal across East Lothian, designed by a structural engineer and built under a building warrant.
- Survey, design and installation in one
- Covering EH21, EH31, EH32, EH33
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Load-bearing wall removal in East Lothian: how it works
Load-bearing wall removal means taking out a wall that holds up floors, roof loads or walls above it, and replacing that support with a steel beam sized by a structural engineer. The beam sits on padstones at each end, the weight above is held on temporary props while the wall comes out, and building standards inspects the finished work.
If you are planning load-bearing wall removal in East Lothian, the order of work matters as much as the steel: survey, calculations, approval, propping, installation, inspection and making good. We can survey in places such as Dunbar, Haddington and Tranent and the villages around them. We run that sequence for you as one job with one point of contact.
Worth knowing before you start
- A building warrant is needed because removing a structural wall is controlled building work. Doing it without approval can cause problems when you come to sell, and putting it right afterwards costs far more than doing it properly first time.
- Homes built before 2000 may contain asbestos in textured ceilings, boxing or old boards. Where there is a risk, a survey of the area being disturbed is arranged before the wall comes out.
- Temporary works matter as much as the beam. Props, spreaders and needles carry the house while the wall is out, and they are positioned so the floor below can take them too.
- The beam size depends on the span, what sits above and how the ends are supported. Two walls that look the same can need very different steel, which is why every beam is sized from calculations rather than guessed.
- Whether a wall is load-bearing is not always obvious. Joists running across the wall, a wall directly above, or the wall sitting on a footing in the floor are common clues, but the engineer's check on site is what settles it.
What happens, step by step
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building warrant
A building warrant is applied for from East Lothian Council, and work starts only once the warrant has been granted.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
Guide prices for load-bearing wall removal in East Lothian
As a guide, budget £1,800–£4,550 including VAT for load-bearing wall removal with steel beam in East Lothian, based on published UK cost guides adjusted for prices in Scotland (-9%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Load-bearing wall removal with steel beam | £1,800–£4,550 | Typical internal wall up to about 4 m: calculations, building standards, propping, steel, padstones, fitting, fire protection and making good |
| Building warrant fee | £215–£435 | Statutory fee set by the estimated value of the work: £215 up to £5,000, rising on a sliding scale (fees from 1 April 2026) |
| Structural calculations for a beam | £230–£680 | Site measure or photos, beam and padstone design and calculations for building standards |
| Kitchen-diner knock-through | £2,300–£5,450 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
Figures include our approximate regional adjustment for prices in Scotland (-9%) and are rounded. How these figures are worked out.
Building control and neighbours in East Lothian
Scottish rules are stricter on timing than in England: the building warrant must be in place before the wall is touched. We prepare the application with the engineer's calculations and submit it to East Lothian Council. The finished work is then certified and a completion certificate submitted for acceptance.
Scotland has no Party Wall Act. Work affecting a shared wall is governed by your title deeds and the general law, and in flats by the Tenements (Scotland) Act 2004, so it is sensible to agree the work with neighbours in writing before starting.
Load-bearing wall removal by town
Questions about load-bearing wall removal in East Lothian
Which towns in East Lothian do you cover?
We cover towns including Musselburgh, Haddington, North Berwick and Dunbar, plus the villages and smaller towns around them.
Can I stay at home while the work is done in East Lothian?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
How do I know if my wall is load-bearing?
Clues include floor joists that run across the top of the wall, a wall directly above it upstairs, and a wall that is solid brick or block rather than a hollow stud partition. None of these is proof on its own. A structural engineer checks on site and confirms it before any work is planned.
Do I need planning permission to remove an internal wall?
Usually not, because internal alterations to a house are not normally development needing planning permission. Listed buildings are different and need listed building consent, and flats normally need the freeholder's or landlord's written consent.
Will the beam show once the job is finished?
It depends on the design. Most beams sit just below the ceiling and are boxed in with plasterboard, leaving a small step. A beam can be set up into the floor void for a flat ceiling, which takes more work, or left exposed and painted where you want an industrial look.
Who sizes the steel beam?
A structural engineer. They look at the span, the loads from floors, walls and roof above, and the bearings at each end, then specify the beam, padstones and any columns. We arrange those calculations, or work to calculations you already have.