Kitchen-diner knock-throughs · Tamworth
Kitchen-diner knock-throughs in Tamworth
Steelwork, approvals and making good for kitchen-diner knock-throughs in Tamworth and nearby.
- Itemised written quote
- Beam sized by a structural engineer
- Covering Tamworth and nearby
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning kitchen-diner knock-throughs in Tamworth
If you live in Tamworth, kitchen-diner knock-throughs can usually be planned and priced after a single survey visit. We also work in nearby Walsall, roughly 12.5 miles away. We cover B77, B78 and B79, and we fix the price in writing once the layout and scope are agreed.
The wall between a kitchen and dining room is often a structural one, especially in semi-detached and terraced houses where it carries the floor joists for the bedrooms above. Opening it up gives the sociable, open-plan space most families want, but the kitchen brings extra things to plan: pipes, cables, an extractor, and a layout that has to work around the new steel.
Worth knowing before you start
- Sinks and dishwashers usually sit on an outside wall, but supply pipes and waste runs sometimes cross the internal wall. Moving the sink to an island means planning a waste route with enough fall under the floor, which affects how the floor is prepared.
- A flush beam sits up within the depth of the ceiling so the kitchen and dining ceilings run as one flat surface. It suits continuous downlights and long runs of wall units, but each joist has to be connected into the beam, which adds labour.
- A gas hob or cooker supply often runs along or through the wall being removed. By law, any work on gas pipework must be carried out by a Gas Safe registered engineer, so the pipe is capped or rerouted by one before the wall comes down.
- In many houses the kitchen and dining room wall carries the bedroom floor joists, and sometimes a bathroom wall above. Lifting a floorboard upstairs to see which way the joists run is a useful first look, though the engineer confirms what the wall actually supports.
- Cooker hood ducting that currently runs out through the wall may need a new route once the wall goes. Ducting can often be run in the ceiling void alongside the beam, but the beam's position and depth need to be known first.
How the job runs in Tamworth
Look and measure
We check the wall, the span you want and what the wall is carrying, and photograph anything the engineer needs to see.
Design and price
Calculations come back from the engineer and we confirm your fixed written price, line by line.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Fit, inspect, finish
The work is propped and the steel installed and packed tight. After inspection the opening is boxed, plastered and left clean.
Guide prices for kitchen-diner knock-throughs in Tamworth
As a guide, budget £2,500–£6,000 including VAT for kitchen-diner knock-through in Tamworth, based on published UK cost guides adjusted for prices in the West Midlands (no adjustment).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Kitchen-diner knock-through | £2,500–£6,000 | Internal structural wall between kitchen and dining room, steel beam, approvals and making good (kitchen fitting extra) |
| Fire protection to a steel beam | £150–£600 per beam | Fire-rated board boxing or an intumescent coating system as specified |
| Structural calculations for a beam | £250–£750 | Site measure or photos, beam and padstone design and calculations for building control |
| Load-bearing wall removal with steel beam | £2,000–£5,000 | Typical internal wall up to about 4 m: calculations, building control, propping, steel, padstones, fitting, fire protection and making good |
Figures include our approximate regional adjustment for prices in the West Midlands (no adjustment) and are rounded. How these figures are worked out.
Building control and neighbours in Tamworth
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Kitchen-diner knock-throughs near Tamworth
- Lichfield 6.3 mi
- Sutton Coldfield 6.9 mi
- Aldridge 9.5 mi
- Burntwood 10.2 mi
- Swadlincote 11.3 mi
- Aston 12.2 mi
Kitchen-diner knock-throughs in Tamworth: your questions
Do I need a party wall agreement for kitchen-diner knock-throughs in Tamworth?
Yes, if the beam bears into a shared wall: the Party Wall etc. Act 1996 applies in England and Wales, and a party structure notice must be served at least two months before that work starts. We arrange it through a party wall surveyor.
Who approves kitchen-diner knock-throughs in Tamworth?
Structural work in Tamworth needs a building notice or full plans application to the local council's building control team or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Can the steel beam be hidden in the ceiling?
Yes, a flush beam can be set into the ceiling void so there is no step between the kitchen and dining ceilings. It needs enough joist depth and more labour to connect the joists to the steel, so it costs more than a downstand. The engineer confirms whether it is possible in your house.
Should I do the knock-through before or after fitting a new kitchen?
Before. The steel, any column, the floor levelling and the plastering all need to be finished first, so the kitchen fitter works in a dry, square room with services already in position. Fitting units and then taking out a wall risks damage and rework, and the beam position can affect where wall units go.
Can I knock my kitchen and dining room into one?
In most houses, yes. The wall can be removed even if it is load-bearing, as long as a steel beam designed by a structural engineer takes over the load and building control approves the work. The main things to check early are what the wall carries, where services run, and whether the layout still works around any column.
Do you also work near Tamworth?
Yes. We also cover nearby towns including Lichfield, Sutton Coldfield, Aldridge and Burntwood.