Garage conversion openings · Feltham
Garage conversion openings in Feltham
Garage conversion openings in Feltham, from free survey to completion certificate.
- Price fixed in writing once scope is agreed
- Building control arranged
- Temporary works and making good included
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
About our garage conversion openings service in Feltham
We cover garage conversion openings in Feltham (TW2, TW3, TW4) and the streets around it. Our coverage runs across London, so nearby villages are included too. Each job is designed by a structural engineer and approved through local building control before work begins.
Converting a garage is a popular way to add a room without extending. Structurally, two things usually happen: the big garage door opening is filled in with a wall, window or door on proper foundations, and a doorway or wider opening is formed through the wall between the garage and the house.
Key points for your project
- Once the garage becomes a habitable room, the energy efficiency requirements of the building regulations apply. Walls, floor and roof normally need insulating to current standards, so the structural design and the thermal upgrade are planned together.
- An integral garage is usually separated from the house by fire-resisting construction. If part of it stays as a garage or store, that separation must be kept, and any new door between garage and house normally needs to be a fire door.
- Garage floors often sit lower than the house floor and may have no damp-proof membrane. The infill wall needs a damp-proof course linked to the existing walls, and the floor usually needs a membrane, insulation and screed raised to the house level.
- The beam or lintel over a garage door was designed to span an open gap. It may be timber, concrete or steel, and in older houses it can be undersized or corroded, so the engineer checks it before anything is built underneath or above it.
- The structural part of a garage conversion, covering the infill foundation, the wall and any new opening, typically takes one to two weeks. The full conversion with insulation, electrics, plastering and flooring takes longer, depending on the scope.
From survey to sign-off in Feltham
Survey in Feltham
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
What do garage conversion openings cost in Feltham?
As a guide, budget £1,300–£3,850 including VAT for garage door opening infill (structural part) in Feltham, based on published UK cost guides adjusted for London prices (+28%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Garage door opening infill (structural part) | £1,300–£3,850 | Beam or lintel checked or replaced, foundation and infill wall for the old door opening (window and finishes extra) |
| Widening an internal doorway | £1,300–£3,200 | Opening widened with a new lintel or short beam, approval where structural, and making good |
| Building control fees | £320–£830 | Building notice or full plans fee and inspections; varies by council or approver |
| Lintel replacement | £510–£1,540 per lintel | Propping, removing the old lintel, new lintel set on beds and brickwork made good |
Figures include our approximate regional adjustment for London prices (+28%) and are rounded. How these figures are worked out.
Building rules for Feltham
Structural openings in English homes need building regulations approval before work starts. The local council's building control team can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Local questions answered
What happens at the survey visit in Feltham?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
How much do garage conversion openings cost in Feltham?
As a guide, budget £1,300–£3,850 including VAT for garage door opening infill (structural part) in Feltham, based on published UK cost guides adjusted for London prices (+28%). The exact figure depends on the span, what the wall carries, access and the finish, and is fixed in writing once the scope is agreed.
How long do the structural works for a garage conversion take?
Typically one to two weeks for the structural stage: digging and concreting the infill foundation, building the infill wall, and forming any new opening into the house. Building control inspections fit around these stages, and the insulation, electrics, plastering and flooring of the conversion follow on afterwards.
Does the infill wall need foundations?
Yes. A new masonry wall across the garage door opening needs a proper footing, as the existing garage slab is usually not designed to carry it. A trench is dug across the opening and a foundation is formed to the engineer's and building control's requirements, then inspected before the wall is built.
What happens to the beam over my garage door?
It is checked by the engineer. Many can stay, carrying the wall above as before, with the infill built underneath. If it is timber that has rotted, a corroded steel section or simply undersized for the loads, it is replaced, with the wall or room above propped while the new steel goes in.