Bi-fold & sliding door openings · Leeds
Bi-fold & sliding door openings in Leeds
Bi-fold & sliding door openings in Leeds, from free survey to completion certificate.
- Survey, design and installation in one
- Covering LS1, LS2, LS3
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
Planning bi-fold & sliding door openings in Leeds
Leeds has a mix of housing, and bi-fold & sliding door openings need a slightly different approach in each. The wider West Yorkshire area is covered as well. Whatever the age of the property, the steel goes in on proper bearings with temporary support in place throughout.
We coordinate the structure with your door supplier's sizes, so the finished opening matches the frame. The survey visit, structural calculations from a qualified engineer, building control, propping, steel, cavity trays, weather protection while the wall is open and making good are all covered in one itemised written quote.
What to expect
- Both leaves of a cavity wall need support over the opening. Depending on the design, the outer brickwork may sit on a plate fixed to the beam or on a separate external lintel, and the engineer specifies which suits the loads and the look.
- New glazed doors must meet the energy efficiency requirements of the building regulations, and a wide opening adds a large area of glazing to the house. The door supplier normally provides the performance data that building control needs.
- External walls can have gas meters, boiler flues, soil pipes, outside taps or cables near the new opening. These are found at survey and moved by the right trade, with any gas pipework done by a Gas Safe registered engineer as the law requires.
- The house is open to the weather between taking out the wall and fitting the doors. Temporary sheeting or a boarded frame keeps rain out and the house secure, so the gap between the structural work and door fitting should be kept short.
- Replacing a rear window with doors in a house is usually permitted development, but front elevations, listed buildings, flats and homes where permitted development rights have been removed may need planning permission or another consent.
How the job runs in Leeds
Survey in Leeds
We visit, look at the wall and what sits above it, measure the opening and note services, access and how the steel can be brought in.
Engineer's design
A structural engineer sizes the beam, padstones and any posts, and sets out the temporary support needed while the wall is out.
Building control
We submit a building notice or full plans application to Leeds City Council, so approval is in place before the wall is touched.
Install and sign-off
Props go in, the opening is formed, the steel is set and packed, building control inspects it, and we make good.
Guide prices for bi-fold & sliding door openings in Leeds
As a guide, budget £2,400–£6,650 including VAT for rear wall opening for bi-fold or sliding doors in Leeds, based on published UK cost guides adjusted for prices in Yorkshire and the Humber (-5%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Rear wall opening for bi-fold or sliding doors | £2,400–£6,650 | External wall opened up to about 5 m with steel, propping, cavity tray and making good (doors supplied separately) |
| RSJ supply and fit (single beam) | £760–£2,380 per beam | Beam supplied, delivered, lifted and packed on padstones, with propping (calculations and approval priced separately) |
| Lintel replacement | £380–£1,140 per lintel | Propping, removing the old lintel, new lintel set on beds and brickwork made good |
| Widening an internal doorway | £950–£2,380 | Opening widened with a new lintel or short beam, approval where structural, and making good |
Figures include our approximate regional adjustment for prices in Yorkshire and the Humber (-5%) and are rounded. How these figures are worked out.
Building control and neighbours in Leeds
Structural openings in English homes need building regulations approval before work starts. Leeds City Council can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Questions about bi-fold & sliding door openings in Leeds
Who approves bi-fold & sliding door openings in Leeds?
Structural work in Leeds needs a building notice or full plans application to Leeds City Council or a registered building control approver. We prepare and submit it with the structural engineer's calculations and arrange the inspections, so the completion paperwork follows the job.
Can you work on older or listed homes in Leeds?
Yes. Older homes often have lime mortar, timber lintels or shallow footings, which the engineer allows for. Listed buildings need listed building consent for internal structural changes as well as building regulations approval, and that must be in place first.
How wide can a bi-fold door opening be?
There is no fixed limit, as it depends on the loads above and what the beam can bear on. The engineer designs the steel and, for very wide openings or ones near a corner, may specify columns or a goalpost frame. The door system's own maximum panel sizes and configurations also need checking.
Should I order my doors before the opening is made?
It helps to choose them first. The supplier's structural opening size and threshold detail feed into the steel design, so the opening is formed to suit the doors exactly. Many people order once the engineer has confirmed the opening, then time the structural work so the gap is weathered for as short a time as possible.
How long does it take to make an opening for bi-fold doors?
The structural opening usually takes three to five working days, including propping, cutting out the wall, fitting the steel and outer leaf support, and forming the reveals. The doors can then be fitted, with inside making good and outside brickwork finishing following on. Lead times on made-to-order doors affect the overall timeline more than the steelwork.
How much do bi-fold & sliding door openings cost in Leeds?
As a guide, budget £2,400–£6,650 including VAT for rear wall opening for bi-fold or sliding doors in Leeds, based on published UK cost guides adjusted for prices in Yorkshire and the Humber (-5%). The exact figure depends on the span, what the wall carries, access and the finish, and is fixed in writing once the scope is agreed.