Bi-fold & sliding door openings · Gillingham
Bi-fold & sliding door openings in Gillingham
Steelwork, approvals and making good for bi-fold & sliding door openings in Gillingham and nearby.
- Free survey visit in Gillingham
- Engineer's calculations arranged
- Building control handled for you
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What bi-fold & sliding door openings involve in Gillingham
Gillingham has a mix of housing, and bi-fold & sliding door openings need a slightly different approach in each. The wider Kent area is covered as well. Whatever the age of the property, the steel goes in on proper bearings with temporary support in place throughout.
We coordinate the structure with your door supplier's sizes, so the finished opening matches the frame. The survey visit, structural calculations from a qualified engineer, building control, propping, steel, cavity trays, weather protection while the wall is open and making good are all covered in one itemised written quote.
What to expect
- Very wide openings, or ones that run close to the corner of the house, may leave too little wall for the beam to bear on. In that case the engineer may specify steel columns or a goalpost frame standing on its own foundations.
- External walls can have gas meters, boiler flues, soil pipes, outside taps or cables near the new opening. These are found at survey and moved by the right trade, with any gas pipework done by a Gas Safe registered engineer as the law requires.
- Level or flush thresholds are popular with bi-fold doors, but the floor inside and the patio outside need planning together. Drainage at the threshold and a proper damp-proof detail stop water running in when the outside is close to floor level.
- The house is open to the weather between taking out the wall and fitting the doors. Temporary sheeting or a boarded frame keeps rain out and the house secure, so the gap between the structural work and door fitting should be kept short.
- Width, what sits above, whether columns or a goalpost are needed, outer leaf support, threshold works and how much brickwork needs matching all affect the price. The doors themselves are normally supplied separately unless agreed otherwise.
Four stages, one team
Free visit
A short visit to Gillingham to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to Medway Council, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
Guide prices for bi-fold & sliding door openings in Gillingham
As a guide, budget £2,800–£7,850 including VAT for rear wall opening for bi-fold or sliding doors in Gillingham, based on published UK cost guides adjusted for prices in the South East (+12%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Rear wall opening for bi-fold or sliding doors | £2,800–£7,850 | External wall opened up to about 5 m with steel, propping, cavity tray and making good (doors supplied separately) |
| Widening an internal doorway | £1,100–£2,800 | Opening widened with a new lintel or short beam, approval where structural, and making good |
| Lintel replacement | £450–£1,340 per lintel | Propping, removing the old lintel, new lintel set on beds and brickwork made good |
| Structural calculations for a beam | £280–£840 | Site measure or photos, beam and padstone design and calculations for building control |
Figures include our approximate regional adjustment for prices in the South East (+12%) and are rounded. How these figures are worked out.
Building rules for Gillingham
Structural openings in English homes need building regulations approval before work starts. Medway Council can deal with it, or you can use a registered building control approver. Either way the steel is inspected before it is covered, and a completion certificate is issued at the end. Keep it safe for when you sell.
If the beam bears into a wall you share with a neighbour, the Party Wall etc. Act 1996 applies, and a party structure notice must be served at least two months before that work starts. We arrange this through a party wall surveyor.
Local questions answered
Do you cover Gillingham for bi-fold & sliding door openings?
Yes. We carry out bi-fold & sliding door openings in Gillingham and the ME1, ME2, ME3, ME4 and ME5 postcode districts. Book a free survey visit and we will check the wall, arrange the engineer's calculations and send an itemised written quote.
Can I stay at home while the work is done in Gillingham?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
How long does it take to make an opening for bi-fold doors?
The structural opening usually takes three to five working days, including propping, cutting out the wall, fitting the steel and outer leaf support, and forming the reveals. The doors can then be fitted, with inside making good and outside brickwork finishing following on. Lead times on made-to-order doors affect the overall timeline more than the steelwork.
Do I need planning permission for bi-fold doors?
Usually not for a rear opening in a house, as this generally falls within permitted development. Planning or another consent may be needed for front elevations, flats, listed buildings, conservation areas with extra controls, or homes where permitted development rights have been removed. We flag this at survey so you can check before work is booked.
Can I have a level threshold with bi-fold doors?
Often yes, but it has to be designed. The inside floor, outside paving and drainage all need to work together so water cannot run in, usually with a drainage channel outside and the right damp-proof detail under the door frame. We look at levels at the survey and plan the threshold with the door supplier.