Bi-fold & sliding door openings · Poole
Bi-fold & sliding door openings in Poole
Bi-fold & sliding door openings for homes in BH12, BH13, BH14, designed by a structural engineer.
- Survey, design and installation in one
- Covering BH12, BH13, BH14
- Inspected before it is covered
- Free survey visit
- Engineer's calculations arranged
- Building control handled
- Fixed written price once scope is agreed
- England, Wales, mainland Scotland & NI
What bi-fold & sliding door openings involve in Poole
Planning bi-fold & sliding door openings in Poole? Our team covers BH12, BH13, BH14, BH15 and BH17 and the streets around them. Our coverage runs across Dorset, so nearby villages are included too. You get one written quote for the calculations, approvals, propping, steel and making good.
Replacing a window or narrow patio door with a full run of bi-fold or sliding doors opens a room to the garden. Because it is an external wall, the opening usually carries the first floor, the wall above and sometimes roof loads, and the new steel has to work with the doors as well as hold the house up.
Key points for your project
- Level or flush thresholds are popular with bi-fold doors, but the floor inside and the patio outside need planning together. Drainage at the threshold and a proper damp-proof detail stop water running in when the outside is close to floor level.
- Both leaves of a cavity wall need support over the opening. Depending on the design, the outer brickwork may sit on a plate fixed to the beam or on a separate external lintel, and the engineer specifies which suits the loads and the look.
- The structural work for a typical bi-fold opening usually takes three to five working days. Doors are often made to order, so the steel goes in once opening sizes are confirmed and the doors are fitted soon after.
- Door suppliers quote a structural opening size, which allows for the frame and fixing tolerances. Agreeing that size before the steel is designed avoids reveals that are too tight or gaps that have to be packed out later.
- Very wide openings, or ones that run close to the corner of the house, may leave too little wall for the beam to bear on. In that case the engineer may specify steel columns or a goalpost frame standing on its own foundations.
Four stages, one team
Free visit
A short visit to Poole to see the job, agree what you want and check the bearings, floors and services that affect the design.
Calculations
The engineer's calculations and a simple drawing are prepared for your opening and shared with you before anything is ordered.
Building control
We submit a building notice or full plans application to the local council's building control team, so approval is in place before the wall is touched.
Steel in, made good
On site we prop, open up, fit and pack the steel, then fire protect, box in and plaster once the inspection is done.
How much should I budget in Poole?
As a guide, budget £2,600–£7,200 including VAT for rear wall opening for bi-fold or sliding doors in Poole, based on published UK cost guides adjusted for prices in the South West (+3%).
| Job | Typical guide range | What it usually covers |
|---|---|---|
| Rear wall opening for bi-fold or sliding doors | £2,600–£7,200 | External wall opened up to about 5 m with steel, propping, cavity tray and making good (doors supplied separately) |
| Structural calculations for a beam | £260–£770 | Site measure or photos, beam and padstone design and calculations for building control |
| Widening an internal doorway | £1,050–£2,600 | Opening widened with a new lintel or short beam, approval where structural, and making good |
| Opening into a rear extension | £2,600–£7,200 | Original rear wall removed with a beam or goalpost, approvals and propping, coordinated with the extension build |
Figures include our approximate regional adjustment for prices in the South West (+3%) and are rounded. How these figures are worked out.
Building rules for Poole
For Poole, building control is provided by the local council's building control team, or by a registered building control approver if preferred. We send them the engineer's calculations with a building notice or full plans application and book the inspections. Work done without approval can cause problems at sale and is far dearer to put right later.
Terraced and semi-detached homes often need party wall notices, because cutting into a shared wall to take a beam end is notifiable under the Party Wall etc. Act 1996. Allow at least two months for the notice period unless your neighbour agrees sooner.
Bi-fold & sliding door openings near Poole
- Bournemouth 4.6 mi
- Christchurch 9.0 mi
- New Milton 14.2 mi
- Weymouth 21.9 mi
Local questions answered
What happens at the survey visit in Poole?
We look at the wall, the floor and ceiling either side and what sits above, measure the opening you want, and note cables, pipes and access for the steel. It usually takes under an hour and there is no charge.
Can I stay at home while the work is done in Poole?
Usually, yes. The work area is screened and floors are protected. The rooms either side of the opening are out of action for a few days, and there is some noise and dust while the masonry comes out.
Should I order my doors before the opening is made?
It helps to choose them first. The supplier's structural opening size and threshold detail feed into the steel design, so the opening is formed to suit the doors exactly. Many people order once the engineer has confirmed the opening, then time the structural work so the gap is weathered for as short a time as possible.
Why does the beam need to be stiffer for glazed doors?
Because glazed doors tolerate very little movement. Every beam bends slightly under load, and with bi-folds or sliders that movement can make panels bind, tracks drag or glass crack. The engineer sets a stricter deflection limit for these openings, which often means a heavier section than strength alone would need.
How long does it take to make an opening for bi-fold doors?
The structural opening usually takes three to five working days, including propping, cutting out the wall, fitting the steel and outer leaf support, and forming the reveals. The doors can then be fitted, with inside making good and outside brickwork finishing following on. Lead times on made-to-order doors affect the overall timeline more than the steelwork.